1.防跑偏保護裝置
Anti-deviation protection device
防跑偏保護裝置的作用是，在輸送帶發生跑偏時，使輸送帶自動糾偏;在嚴重跑偏時，使輸送機自動停機。
The function of anti-deviation protection device is to automatically correct the deviation of the conveyor belt when the deviation occurs. In the serious deviation, the conveyor automatically stop.
1)在用帶式輸送機在機頭和機尾均安裝一組跑偏保護傳感器，當膠帶運輸機的膠帶發生跑偏時，膠帶推動臂式滾動導杆，當偏離夾角大於200mm(允許誤差±30mm)時，跑偏開關動作，保護器主機開報警，但不造成停機，保護器主機經過5-10s延時後，如膠帶仍處於跑偏狀態，保護器主機將自動切斷電源，實現跑偏保護。
In the belt conveyor in the nose and tail are ins-talled a set of wandering to protect sensor, wh-en the belt conveyor belt running deviation oc-curs, the tape drive arm type rolling guide rod, when the deviation Angle is greater than 200 mm (allowed error of plus or minus 30 mm), running deviation switch action, protector open alarm host, but not cause downtime, protector host after 5 to 10 s delay, such as the belt is still in the running state, protector host will au-tomatically cut off power supply, protection imp-lementation wandering.
2)帶式輸送機中間部分每隔30至50米處安裝一組防跑偏輪，防跑偏裝置應安裝在距離槽形託輥外沿50-100mm範圍內，以阻礙皮帶跑偏。
A set of anti-deviation wheels shall be installed in the middle part of the belt conveyor at inter-vals of 30 to 50 meters. The anti-deviation device shall be installed within a range of 50-100mm from the outer edge of the groove idler to prevent belt deviation.
2.防滑保護裝置
Anti-skid protection device
防滑保護裝置的作用是當驅動滾筒與輸送帶打滑摩擦時，使帶式輸送機自動停機。
The function of the anti-slip protection device is to stop the belt conveyor automatically when the driving drum and the belt slip and friction.
磁鐵式：防滑保護裝置應將磁鐵安裝在從動滾筒的側面，速度傳感器要安裝在與磁鐵相對應的支架上，當皮帶機滾筒轉速低於設定值並保持5秒鐘時，皮帶機將自動斷電停機。
Magnet type: the anti-slip protection device sha-ll install the magnet on the side of the driven roller, and the speed sensor shall be installed on the bracket corresponding to the magnet. When the speed of the belt conveyor roller is lower than the set value and maintained for 5 seconds, the belt conveyor will automatically cut off the power and stop.
3.堆煤保護裝置
Coal pile protection device
堆煤保護裝置的作用是當皮帶輸送機機頭發生堆煤時，使帶式輸送機自動停機。
The role of the coal stacking protection device is to automatically stop the belt conveyor when the belt conveyor's head is loaded with coal.
堆煤保護裝置安裝一般分兩種情況：
There are generally two types of installation of coal pile protection device:
一種是安裝在煤倉上口，堆煤保護傳感器的安裝高度，應在低於機頭下膠帶200mm水平以下，其平面位置應在煤倉口範圍之內，當煤堆積觸及到堆煤保護探頭時，保護器將自動停機報警。
One is installed at the top of the bunker. The installation height of the bunker protection sen-sor should be below the 200mm level of the rubber belt under the machine head, and its pla-ne position should be within the scope of the bunker opening. The protector will automatically stop and alarm when the coal accumulation tou-ches the bunker protection probe.
另一種是安裝在兩部帶式輸送機搭接處，在兩部皮帶機搭接處堆煤保護傳感器的安裝高度，應在後部輸送機機頭滾筒軸線水平以下，其平面位置應在前部膠帶機的煤流方向，且距離應在前部膠帶機機架側向200-300mm，當堆煤觸及到堆煤保護探頭時，保護器將自動停機報警。
Another is installed on the two belt conveyor by it, put it on two belt conveyor of coal to protect sensor installation height, the nose should be in the back of the conveyor roller axis below the level and the front of the plane position should be in the coal flow direction of tape machine, and the distance should be at the front of the tape machine frame lateral 200-300 - mm, when the heap protection probe touched the pile of coal, coal saver will automatically stop the alarm.
這就是今天皮帶輸送機的介紹。如果您想了解更多信息，請訪問我們的網站。
This is the introduction of the belt conveyor today. If you would like to learn more, please visit our website.